To begin repairing your adult TPE sex dolls, the first tool you'll need is an infrared gun with a power output of 1.5 Kilowatts. It is useful because it displays real-time temperature feed. You can buy it on Amazon or anywhere else online. Meanwhile, the repairs you perform will vary depending on the nature of the damage. For example, if the damage is minor, the repair process will be straightforward and will not necessitate much effort or skill.
Because of the impact of weight, your sex doll may have an indentation mark. Such pressure marks typically appear when you press the surface of your sex doll with heavy items. The same effect can be seen if you lay her incorrectly without considering the importance of correct position or posture. You can, however, relax and not be concerned because there is a tried-and-tested procedure you can use.
THE PROCESS OF USING HOT TOWELS
For a short period of time, cover the visible pressure dents with a hot, clean towel. Wearing a glove, pat the same area with your hand. Repeat the process until the indentation is gone.
METHOD OF USING A HAIR DRYER
A hairdryer appears to be a versatile accessory. While most people believe that a hairdryer is only for drying wet dreadlocks, it also provides a solution for TPE sex doll repair work.
Grab a wet, clean white cloth to get started. Then, using the cloth, cover the pressure marks and heat the surface. Repeat the process for a certain amount of time. The pressure marks and indentation on the surface of your sex doll will gradually fade away.
HOW CAN TEARS AND ABRASIONS BE REPAIRED?
EASY FIX FOR NECK OR LEG RIP, ARM TEAR, OR ABRASION
If you use your sex doll in an inappropriate and rash manner, it will pose a structural hazard and cause damage. That being said, there are two approaches to repairing this particular TPE issue.
APPLYING TPE GLUE - THE FIRST CHOICE
To make this process work, locate the torn/damaged portion and apply TPE glue to it with a fine-tipped tool. Then, bring the two sides of the laceration together. Holding the patch for a minute or two will restore it to its original state.
GLUE APPLICATION PROCEDURE:
- To begin, clean up any dirt or excess oil from the critical area to be treated. You can accomplish this by wiping the area with 70% isopropyl alcohol.
- Open the wound with a glove-clad hand.
- Then, using a spatula, evenly apply the TPE repair coating solvent to the wound's inner surface. Meanwhile, avoid having excess glue hanging off the tip of your spatula and replace the cap on the glue bottle to prevent the solvent from evaporating.
- On both sides, rub the spatula against the inside of the tear.
- Pull the two sides of the tear together and allow the TPE repair solvent to bind the wound back together. For a while, keep the wound closed.
- Wipe away any excess that has been squeezed out of the bound back tear with a tissue or a clean cloth. While doing so, do not use your fingers to avoid leaving unwanted prints and impressions.
- Check for any tension on the doll's surface that could put strain on the re-joined wound.
- Place the doll safely, so that there is no tension on the critical surface for the next 24 hours.
PRO TIPS: GETTING THE DOLL READY FOR THE PROCEDURE
Consider cleaning the damaged area with a cleanser, soap, nail polish remover, or make-up remover to maximize the effectiveness of the TPE glue. Meanwhile, make sure there are no water stains on the doll's skin. Keep it dry and clean at all times.
PUT THE SEX DOLL IN THE RIGHT PLACE
Having said that, it is critical to consider the sex doll's posture. Ascertain that the wound area is in a horizontal position. This ensures that the amount of glue applied remains confined within the wound and does not overflow from the breakage. Meanwhile, being meticulous and careful is essential. Each step necessitates minute accuracy; otherwise, the outcome will be far from satisfactory. There will be uneven bonding, which will ruin the symmetry of the sex doll.
THE HEAT GUN PROCEDURE FOR FIXING TPE SKIN
ABRASIONS
The most common types of heat guns available online are the 1.5 Kilowatt ones. They have the advantage of having an attached temperature sensor that allows you to monitor the amount of heat applied. They have a digital interface and perform admirably.
PROCEDURE
WASH THE SURFACE
To begin, cleanse the skin's surface with either baby oil or vaseline. This section is critical because it serves two functions - one, you will have a clean and sterile skin surface, and two, the heat applied will be more evenly distributed. Applying oil is therefore critical if you do not want to burn your doll’s skin.
APPLY HEAT GUN TO AFFECTED AREA
Then, with the heat gun pointed at the skin, proceed. Keep a safe distance between the device and the doll's skin. If you focus it too closely, it will cause severe burns and cause a disaster. Keep a four-inch distance from the wound area on the skin of your adult TPE sex doll.
A test piece of the TPE material will be extremely useful. You can easily obtain one by contacting a nearby TPE vendor. You can use it to practice while keeping the melting temperature of the TPE material in mind. Before you take the plunge, familiarize yourself with the proper parameters for the application of heat.
ACHIEVING THE DESIRED TEMPERATURE
The average melting temperature of TPE is around 110 degrees Celsius. Heating it creates a glaze that looks like mirror finish. The intensity of fumes coming out of the heating will tell you when to stop increasing the temperature. Heat your sex doll's skin to the desired temperature.
CAREFULLY FIX THE ABRASION
Using a feathered cloth, smooth out the surface irregularities caused by the abrasion. Maintain several iterations of heating and cooling and repeat the process several times. This is the key to achieving a fine finish because each time you repeat the heat-and-cool procedure, it becomes smoother.
Meanwhile, you've got thirty seconds to work on smoothing out the abrasion. Needless to say, the temperature drops quickly, and you must seize the opportunity to do as much smoothing work as possible.
ABRASION FIXING GUIDELINES
Repeated heating and cooling the adult life likeTPE sex dolls will cause the oil to dry out. And so, you will have to reapply the oil after each iteration. This is critical because keeping it moist will ensure a good finish.
However, after several repetitions of the heating and cooling process, you will see a satisfactory result. When you're finished, dust with powder for a flawless finish. The powder is extremely useful in this situation because it blends in with the texture and makes the repair virtually invisible.
To avoid the health risks associated with unwanted fume inhalation, make sure you're in an open area and wearing a mask.
Also, because you are using a high-temperature device, use the infrared gun with caution to avoid overheating or burning.
REPAIRING DOLL’S FACIAL CUTS
Repairing facial cuts and tears on these love dolls for men requires a similar setup but a lot more practice. Small facial cuts on your sex doll can be repaired with a steady hand and the right tools.
If you are trying for the first time, we recommend that you buy a new head for your sex doll instead. This will completely transform your real doll and is well worth the money.
Most genuine branded doll heads will cost you less than $400 USD, which is a fantastic deal. It's not just a new head; it's an extra head with distinct features. The same doll body can now have two distinct appearances and personas.
